LILO 開機訊息

LILO start messages

When LILO loads itself, it displays the word "LILO".
Each letter is printed before or after performing some specific action.
If LILO fails at some point, the letters printed so far can be used to identify the problem.
This is described in more detail in the technical overview.

Note that some hex digits may be inserted after the first "L" if a transient disk problem occurs.
Unless LILO stops at that point, generating an endless stream of error codes, such hex digits do not indicate a severe problem.

(nothing)
No part of LILO has been loaded.
LILO either isn't installed or the partition on which its boot sector is located isn't active.

L (error)...
The first stage boot loader has been loaded and started, but it can't load the second stage boot loader.
The two-digit error codes indicate the type of problem. (See also section "Disk error codes".)
This condition usually indicates a media failure or a geometry mismatch (e.g. bad disk parameters, see section "Disk geometry").

LI
The first stage boot loader was able to load the second stage boot loader, but has failed to execute it.
This can either be caused by a geometry mismatch or by moving /boot/boot.b without running the map installer.

LIL
The second stage boot loader has been started, but it can't load the descriptor table from the map file.
This is typically caused by a media failure or by a geometry mismatch.

LIL?
The second stage boot loader has been loaded at an incorrect address.
This is typically caused by a subtle geometry mismatch or by moving /boot/boot.b without running the map installer.

LIL-
The descriptor table is corrupt. This can either be caused by a geometry mismatch or by moving /boot/map without running the map installer.

LILO
All parts of LILO have been successfully loaded.

+---------------------------------------------------------------+
<譯文>LILO 啟動訊息


當LILO自行載入時，它會顯示LILO一字。在執行某些特定的動作之前或之後會列印每一個字母。
如果LILO在某一點失敗，則目前為止已印出的字母可用來識別問題。

請注意，如果發生暫態磁碟問題，則在第一個"L"之後可插入某些十六進位數字。
除非LILO在該點停止，產生無限的錯誤碼串流，這種十六進位數字不表示伺服器問題。

[無]
未載入 LILO 的任何部件。 LILO 不是未安裝就是其啟動區段所在的分割區不在作用中。

L [錯誤] ...
第一階段啟動載入程式已載入並啟動，但是它無法載入第二階段啟動載入程式。
二位數字錯誤碼指出問題的類型。 這種狀況通常表示媒體失效或幾何不符(例如，磁碟參數無效)。

LI
第一階段啟動載入程式已能夠載入第二階段啟動載入程式，但是無法加以執行。
這可能是由於幾何不符或是沒有執行 map 安裝程式而移動 /boot/boot.b所導致。

LIL
第二階段啟動載入程式已啟動，但是它無法從映射檔載入描述子表格。
這通常是由於媒體失效或幾何不符所導致。

LIL?
在不正確的位址載入了第二階段啟動載入程式。
這通常是由於細微的幾何不符或是沒有執行 map 安裝程式而移動 /boot/boot.b 所導致。

LIL-
描述子表格訛誤。這可能是由於幾何不符或是沒有執行 map 安裝程式而移動/boot/map 所導致。

LILO
已順利載入 LILO 的所有部件。

+---------------------------------------------------------------+

http://users.bigpond.net.au/hermanzone/p4.html


http://www.study-area.org/linux/system/linux_boot.htm